Free Shop Tools

Free CNC Feeds & Speeds and V-Carve Inlay Calculators

Calculate chip load, IPM and mm/min feed rates, pass depths, and gap-free V-Carve Inlay pocket and plug settings right in your browser. No login required.

CNC Feeds, Speeds & Chip Load Calculator

Pick your stock material to load conservative desktop CNC router presets, or enter your own bit diameter, flutes, RPM, and target chip load using Feed = RPM x Flutes x Chip Load.

Cutting Parameters

Units

Changing the material loads conservative starter RPM, flutes, and chip load.

Flute Count

Typical 1/4" hardwood starting range: 0.0020" to 0.0040" (0.05 to 0.10 mm).

Recommended Starting Cut Settings

Feed Rate 85 IPM 2159 mm/min
Plunge / Ramp Rate 24 IPM 605 mm/min (ramp >= 4xD)
Conservative Pass Depth 0.150" 3.81 mm max stepdown
Surface Speed 1113 SFM 339 m/min surface speed
Healthy chip-load range for Hardwood (Walnut, Maple, Oak, Cherry). Use a downcut or compression spiral and ramp in at 4x bit diameter to avoid scorching.

Starter estimates assume a rigid desktop CNC router and sharp carbide tooling. Always verify on scrap stock. Inside VibeCNC, our built-in 640+ Material Database and Smart Machining Engine compute feeds and entry ramps automatically per toolpath.

V-Carve Inlay Depth & Clearance Calculator

Plan gap-free contrasting hardwood V-Carve inlays for cutting boards, trays, and keepsake boxes. Verify seated depth, bottom glue gap, and top bandsaw clearance before cutting.

Inlay Recipe & Depths (Inches)

Matching V-Bit Angle (Both Halves)

Live Cross-Section & Clearances

Seated Inlay Depth 0.150" (3.81 mm)
Bottom Glue Gap 0.050" (1.27 mm)
Top Saw Clearance 0.100" (2.54 mm)
Total Male Cut Depth 0.250" (6.35 mm)
Balanced V-Carve Inlay recipe: 0.150" seated inlay depth, 0.050" glue pocket, and 0.100" saw kerf clearance using matching 60 deg V-bits.

Quick CNC Router Starting Reference (1/4" Carbide End Mill)

Conservative starting points for rigid desktop CNC routers such as Onefinity, Shapeoko, LongMill, and Avid CNC.

Conservative CNC router speeds and feeds for a 1/4" carbide end mill
Material Spindle RPM Feed Rate Max Pass Depth
Softwood (Pine, Cedar) 16,000 - 18,000 RPM 80 - 120 IPM 0.18" - 0.25"
Hardwood (Walnut, Maple, Oak) 16,000 - 18,000 RPM 65 - 100 IPM 0.12" - 0.18"
Baltic Birch Plywood / MDF 18,000 RPM 80 - 120 IPM 0.15" - 0.22"
Cast Acrylic (1-Flute O-Flute) 12,000 - 16,000 RPM 50 - 80 IPM 0.06" - 0.10"
HDPE / Starboard (1-Flute O-Flute) 14,000 - 16,000 RPM 75 - 110 IPM 0.12" - 0.20"
6061 Aluminum (1-Flute ZrN) 10,000 - 14,000 RPM 25 - 45 IPM 0.02" - 0.04"

Calculator FAQ

Quick answers to the most common CNC speeds, feeds, and V-Carve inlay setup questions.

What is the CNC chip load formula?

Feed Rate (IPM) = Spindle RPM x Number of Flutes x Target Chip Load (inches). For metric setups, multiply RPM x Flutes x Chip Load in millimeters to get mm/min.

Why is my CNC router bit burning hardwood?

Dark scorch marks mean the flutes are rubbing instead of cutting clean chips. Either lower your spindle RPM toward 12,000 to 16,000 or raise your feed rate so the bit stays inside its healthy chip-load window, and use easing ramps rather than straight vertical plunges.

What depths should I use for a V-Carve inlay cutting board?

Using matching 60 degree V-bits for both halves, a dependable end-grain cutting board recipe is 0.20" Female Pocket Flat Depth, 0.15" Male Plug Start Depth, and 0.10" Male Plug Flat Depth. That leaves 0.15" of seated inlay, 0.05" for glue compression, and 0.10" for flush-sawing the backing off.

Do I need an account to use these calculators?

No. Both calculators work free in your browser without signing in. Inside the main VibeCNC CAD/CAM workspace, these formulas are integrated directly with 640+ materials, 2,000+ bits, and automatic V-Carve Inlay male/female toolpath generation.